Crown Exterior Semi-Gloss
exterior – waterborne
Technical Data Sheet C01 5-25
This data sheet replaces all previous issues
Crown Exterior Semi-Gloss is formulated with a combination of top quality acrylic emulsions blended with high grade pigment dispersions for a durable and washable exterior semi-gloss finish.
Typical uses
- Blockwork
- Brickwork
- Cement plaster
- Concrete
- Fibre cement
- Roughcast/stucco
- Timber
- Weatherboards
Performance
-
Excellent intercoat adhesion.
-
Excellent adhesion to all suitably prepared cementitious surfaces.
-
Acid and alkali resistant.
-
Resists mould growth.
Limitations
-
Do not apply at temperatures below 10°C or when it is liable to drop below 10°C during the drying period.
-
Will not penetrate chalky or powdery surfaces.
Physical properties
| Vehicle type | Acrylic |
| Pigmentation | Titanium dioxide |
| Solvent | Water |
| Finish | Semi-gloss |
| Colour | Crown White and selected Resene Total Colour System, including BS5252, Multi- Finish, Whites & Neutrals and The Range colours tinted off white View Resene colour charts online or the online Resene colour library |
| Abrasion resistance | Good |
| Chemical resistance | Good |
| Heat resistance | Thermoplastic |
| Solvent resistance | Fair |
| Durability | Excellent |
Surface preparation
All surfaces
Clean the surface thoroughly to remove all dirt, dust and loose material. Ensure the surface is free from oil, grease and mould. If moss and mould are present, treat with Resene Moss & Mould Killer (see Data Sheet D80)
Refer to Resene Surface Information Preparation Data Sheets (SIPDS), available online at www.resene.com/datasheets, for full substrate specific surface preparation information.
All sanding dusts can be harmful. Always wear appropriate protection.
Seek expert advice if working with lead, chromate or asbestos based materials or surfaces.
Priming
| Primer required | Yes, dependent on surface. Ensure the correct substrate primer and/or sealer is used. |
Timber
Crown Acrylic Primer Undercoat (see Data Sheet C06), Resene Quick Dry (see Data Sheet D45) or Resene Wood Primer (see Data Sheet D40).
Matai, Spotted Gum, Totara
Crown Acrylic Primer Undercoat (see Data Sheet C06) or Resene Quick Dry (see Data Sheet D45).
Cementitious surfaces, fibre cement board
Resene Concrete Primer (see Data Sheet D405) or solventborne Resene Sureseal (see Data Sheet D42).
Cementitious plaster render
Resene Limelock (see Data Sheet D809).
G.R.C. panels, glossy concrete, precast concrete panels
Resene ConcreteSeal 3 in 1 (see Data Sheet D409).
Galvanised steel, Zincalume
Resene ArmourX GP Metal Primer (see Data Sheet D411), Resene Galvo One (see Data Sheet D41) or Resene Galvo- Prime (see Data Sheet D402).
Refer to Resene Technical Services or the Resene website, www.resene.com/datasheets, for full substrate specific priming and Resene coating system/specification information.
Application
| Apply by | Brush, speed brush, synthetic fibre roller or spray |
Typical coverage |
10 square metres per litre per coat |
| Dry film thickness | 40 microns at 10 square metres per litre |
| Dry time (minimum) | 45 minutes at 20°C |
| Recoat time (minimum) | 2 hours at 20°C |
| Usual no. of coats | 2 |
| Thinning | Water |
| Clean up | Water |
Stir thoroughly before use. Fill all nail holes and cracked timber after priming. Apply two full coats of Crown Exterior Semi-Gloss allowing dry time between coats.
Precautions
Product stewardship
Return any unwanted product or packaging to the Resene PaintWise recycling service (NZ) or Paintback (AU).
Downloads
Please read the Safety Data Sheet (SDS) before use.
View: